Apacer Memory America의 APzzzPPSS25-R 규격서

Apacer Technology Inc.
1F, No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City, Taiwan, R.O.C
Tel: +886-2-2267-8000 Fax: +886-2-2267-2261
www.apacer.com
RoHS Compliant
Solid State Drive
Apacer Professional 2.5 NAS SSD Product Specifications
August 4, 2020
Version 1.2
Apacer Specifications Overview:
1
© 2020 Apacer Technology Inc.
Specifications Overview:
Compliance with SATA Revision 3.2
SATA 6 Gb/s interface
Backward compatible with SATA 1.5/3
Gb/s interfaces
Capacity
128, 256, 512 GB
1 TB
Performance*
Burst read/write: 600 MB/sec
Sequential read: Up to 550 MB/sec
Sequential write: Up to 500 MB/sec
Random read (4K): Up to 84,000 IOPS
Random write (4K): Up to 86,000 IOPS
Flash Management
Global Wear Leveling
Flash bad-block management
S.M.A.R.T.
TRIM
NAND Flash Type: 3D TLC
MTBF: >2,000,000 hours
Endurance (in Terabytes Written: TBW)
128 GB: 175 TBW
256 GB: 385 TBW
512 GB: 820 TBW
1 TB: 2,065 TBW
Temperature Range
Operating: 0°C to 70°C
Storage: -40°C to 70°C
Supply Voltage
5.0 V ± 5%
Power Consumption*
Active mode: 2,100 mW
Idle mode: 335 mW
Connector Type
7-pin SATA signal connector
15-pin SATA power connector
Form Factor
2.5
Dimensions: 100.00 x 69.85 x 6.90, unit: mm
RoHS Compliant
Warranty: 5 years or TBW (whichever occurs
first)
*Varies from capacities. The values for performances and power consumptions presented are typical and may vary depending
on flash configurations or platform settings. The term idle refers to the standby state of the device.
Apacer
2
© 2020 Apacer Technology Inc.
Table of Contents
1. Product Specifications ......................................................................3
1.1 Performance .................................................................................................................................. 3
1.2 Environmental Specifications ........................................................................................................ 3
1.3 Mean Time Between Failures (MTBF) .......................................................................................... 3
1.4 Endurance ..................................................................................................................................... 4
1.5 Certification and Compliance......................................................................................................... 4
2. Flash Management ............................................................................5
2.1 Bad Block Management ................................................................................................................ 5
2.2 Global Wear Leveling .................................................................................................................... 5
2.3 S.M.A.R.T. ..................................................................................................................................... 5
2.4 TRIM .............................................................................................................................................. 5
3. Electrical Specifications ...................................................................6
3.1 Operating Voltage .......................................................................................................................... 6
3.2 Power Consumption ...................................................................................................................... 6
4. Physical Characteristics ...................................................................7
5. Product Ordering Information ...........................................................8
Apacer Perlnrmance
3
© 2020 Apacer Technology Inc.
1. Product Specifications
1.1 Performance
Performance of Apacer Professional 2.5 SSD is listed below in Table 1-1.
Table 1-1 Performance Specifications
Capacity
128 GB
256 GB
512 GB
1 TB
Sequential Read* (MB/s)
550
550
550
550
Sequential Write* (MB/s)
450
490
490
500
Random Read IOPS** (4K)
65,000
84,000
75,000
80,000
Random Write IOPS** (4K)
81,000
86,000
68,000
75,000
Note:
Results may differ from various flash configurations or host system setting.
*Sequential performance is based on CrystalDiskMark 5.2.1 with file size 1,000MB.
**Random performance measured using IOMeter with Queue Depth 32.
1.2 Environmental Specifications
Environmental specifications of Apacer Professional 2.5 SSD are shown in Table 1-2.
Table 1-2 Environmental Specifications
Environment
Specifications
Temperature
0°C to 70°C (Operating)
-40°C to 70°C (Non-operating)
Vibration
Non-operating: Sine wave, 15(G), 10~2000(Hz),
Operating: Random, 7.69(GRMS), 20~2000(Hz)
Shock
Non-operating: Acceleration, 1,500 G, 0.5 ms
Operating: Peak acceleration, 50 G, 11 ms
1.3 Mean Time Between Failures (MTBF)
Mean Time Between Failures (MTBF) is predicted based on reliability data for the individual
components in Apacer Professional 2.5” SSD. The prediction result for Apacer Professional 2.5” SSD
is more than 2,000,000 hours.
Note: The MTBF is predicated and calculated based on Telcordia Technologies Special Report, SR-
332, Issue 2 method.
Apacer
4
© 2020 Apacer Technology Inc.
1.4 Endurance
The endurance of a storage device is predicted by TeraBytes Written based on several factors related
to usage, such as the amount of data written into the drive, block management conditions, and daily
workload for the drive. Thus, key factors, such as Write Amplifications and the number of P/E cycles,
can influence the lifespan of the drive.
Table 4-4 Endurance Specifications
Capacity
TeraBytes Written
128 GB
175
256 GB
385
512 GB
820
1 TB
2,065
Note:
The endurance of SSD could be estimated based on users’ behaviors, NAND endurance cycles,
and write amplification factor. It is not guaranteed by the flash vendor.
TBW may vary from flash configuration and platform.
1.5 Certification and Compliance
Apacer Professional 2.5” SSD complies with the following standards:
CE
FCC
RoHS
Apacer
5
© 2020 Apacer Technology Inc.
2. Flash Management
2.1 Bad Block Management
Current production technology is unable to guarantee total reliability of NAND flash memory array.
When a flash memory device leaves factory, it comes with a minimal number of initial bad blocks
during production or out-of-factory as there is no currently known technology that produce flash chips
free of bad blocks. In addition, bad blocks may develop during program/erase cycles. Since bad
blocks are inevitable, the solution is to keep them in control. Apacer flash devices are programmed
with ECC, block mapping technique and S.M.A.R.T to reduce invalidity or error. Once bad blocks are
detected, data in those blocks will be transferred to free blocks and error will be corrected by
designated algorithms.
2.2 Global Wear Leveling
Flash memory devices differ from Hard Disk Drives (HDDs) in terms of how blocks are utilized. For
HDDs, when a change is made to stored data, like erase or update, the controller mechanism on
HDDs will perform overwrites on blocks. Unlike HDDs, flash blocks cannot be overwritten and each
P/E cycle wears down the lifespan of blocks gradually. Repeatedly program/erase cycles performed
on the same memory cells will eventually cause some blocks to age faster than others. This would
bring flash storages to their end of service term sooner. Global wear leveling is an important
mechanism that levels out the wearing of all blocks so that the wearing-down of all blocks can be
almost evenly distributed. This will increase the lifespan of SSDs.
2.3 S.M.A.R.T.
S.M.A.R.T. is an abbreviation for Self-Monitoring, Analysis and Reporting Technology, a self-
monitoring system that provides indicators of drive health as well as potential disk problems. It serves
as a warning for users from unscheduled downtime by monitoring and displaying critical drive
information. Ideally, this should allow taking proactive actions to prevent drive failure and make use of
S.M.A.R.T. information for future product development reference.
2.4 TRIM
TRIM, though in capital letters usually, is a memory computation command rather than an
abbreviation. It is mainly a SATA command that enables the operating system to inform the SSD
(Solid State Drive) which blocks of previously stored data are no longer valid, due to erases by the
host or operating system, such as file deletions or disk formatting. Once notified, SSD will begin the
discard of the invalid LBAs and retain more space for itself, in fact, the discarded is no longer
recoverable.
When an LBA is replaced by the operating system, as with overwrite of a file, the SSD is informed that
the originally occupied LBA is determined as no longer in use or invalid. The SSD will not save those
blocks in garbage collected sectors. Noticeably, a file deletion command by host or operating system
never actually erases the actual content, but marks the file as deleted. This issue is even specifically
noticeable for flash based memory devices, such as SSDs. In fact, an SSD will keep garbage
collecting the invalid, previously occupied LBAs, if it is not informed that these LBAs can be erased.
Thus, the SSD would experience a significant performance downfall.
Apacer fi Capacity Mode
6
© 2020 Apacer Technology Inc.
3. Electrical Specifications
3.1 Operating Voltage
Table 3-1 lists the supply voltage for Apacer Professional 2.5 SSD.
Table 3-1 Operating Range
Item
Range
Supply Voltage
5V ± 5% (4.75-5.25V)
3.2 Power Consumption
Table 3-2 lists the power consumption for Apacer Professional 2.5 SSD.
Table 3-2 Power Consumption
Capacity
Mode
128 GB
256 GB
512GB
1 TB
Active (mW)
1,720
1,750
2,000
2,100
Idle (mW)
320
325
335
330
Note:
*All values are typical and may vary depending on flash configurations or host system settings.
**Active power is an average power measurement performed using CrystalDiskMark with 128KB sequential read/write transfers.
Apacer mum. m H. WWW. “m “H “V l‘ V 5“ Ham 5 lunfln mm D m 4 nm rm nm m (—)59 5510 25 6‘ 7m 25 55 in am y, m mm A m a E D t a 0 y 9 I432 W I Data 75 3 3° “*0 3E ‘ ”nun Arum «r um um , a um m! (—j: EMMA-1M mm mm.” "”3“ mm NEHM mm”) a! mm H 0 mm MM 5n 3 5m 3a
7
© 2020 Apacer Technology Inc.
4. Physical Characteristics
Figure 4-1 Physical Dimensions
Apacer
8
© 2020 Apacer Technology Inc.
5. Product Ordering Information
Capacity
Retail P/N
128GB
AP128GPPSS25-R
256GB
AP256GPPSS25-R
512GB
AP512GPPSS25-R
1TB
AP1TPPSS25-R
Note: Valid combinations are those products in mass production or will be in mass production.
Consult your Apacer sales representative to confirm availability of valid combinations and to
determine availability of new combinations.
Apacer
9
© 2020 Apacer Technology Inc.
Revision History
Revision
Description
Date
1.0
Initial release
6/17/2020
1.1
Updated Endurance on Specifications Overview page and 1.4
Endurance
6/23/2020
1.2
Updated warranty period from 3 years to 5 years on
Specifications Overview page
8/4/2020
Apacer saQaQace-rus com amtsaleflapace com 'pjerwcefiapace om sale a ace nl saleSQaQace com on sales IndiaQapace om
10
© 2020 Apacer Technology Inc.
Global Presence
Taiwan (Headquarters)
Apacer Technology Inc.
1F., No.32, Zhongcheng Rd., Tucheng Dist.,
New Taipei City 236, Taiwan R.O.C.
Tel: 886-2-2267-8000
Fax: 886-2-2267-2261
amtsales@apacer.com
U.S.A.
Apacer Memory America, Inc.
46732 Lakeview Blvd., Fremont, CA 94538
Tel: 1-408-518-8699
Fax: 1-510-249-9551
sa@apacerus.com
Japan
Apacer Technology Corp.
6F, Daiyontamachi Bldg., 2-17-12, Shibaura, Minato-Ku,
Tokyo, 108-0023, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018
jpservices@apacer.com
Europe
Apacer Technology B.V.
Science Park Eindhoven 5051 5692 EB Son,
The Netherlands
Tel: 31-40-267-0000
Fax: 31-40-290-0686
sales@apacer.nl
China
Apacer Electronic (Shanghai) Co., Ltd
Room D, 22/FL, No.2, Lane 600, JieyunPlaza,
Tianshan RD, Shanghai, 200051, China
Tel: 86-21-6228-9939
Fax: 86-21-6228-9936
sales@apacer.com.cn
India
Apacer Technologies Pvt Ltd,
1874, South End C Cross, 9th Block Jayanagar,
Bangalore-560069, India
Tel: 91-80-4152-9061/62
Fax: 91-80-4170-0215
sales_india@apacer.com